Zener diode polarity

Status
Not open for further replies.
Joined
Feb 28, 2012
Messages
287
hello forum

Regarding the zener diode, the standard big brass fitting to me, are they all polarity specific or can any zener be put on a Norton. For example, can a zener off a truimph or BSA being negative earth, be put straight on a Norton with positive earth.Wired appropriatly of course. I dont know much about electrics and appreciate any advice.
Best wishes
Bradley
 
B.Rad said:
hello forum

Regarding the zener diode, the standard big brass fitting to me, are they all polarity specific or can any zener be put on a Norton. For example, can a zener off a truimph or BSA being negative earth, be put straight on a Norton with positive earth.Wired appropriatly of course. I dont know much about electrics and appreciate any advice.
Best wishes
Bradley

I would say that a Negative earth Zener could not be "put straight on a Norton with positive earth" as the body of the Zener, i.e. the bit that gets bolted to the frame forms one of the connection points. You could use it if you isolated the Zener from the frame, but you will, as you say, have to wire it appropriately and have to bolt it to(I would imagine) a fairly large heatsink. I assume you have a Mk2 commando?
 
B.Rad said:
Regarding the zener diode, the standard big brass fitting to me, are they all polarity specific

Yes. Zener diodes are polarity specific. The polarity is usually marked on the Zener.

B.Rad said:
For example, can a zener off a truimph or BSA being negative earth

Only 1979-on Triumphs had negative earth electrical systems, before then they were positive earth, and BSAs were also positive earth.

If you've seen a pre-'79 Triumph or any BSA with a negative earth electrical system then it has been converted from pos. earth. This refers to '60s or '70s machines with alternators and Zener diode regulation and not anything dating back to WW2 or before.
 
Thanks to all for this info. it has been helpful.

I know enough that when the smoke escapes from electrics, it does not seem to work. it seems hard to stuff the smoke back in too.

thanks again
Bradley
 
The 850 E-Bay chopper I sold recently had a negative-ground wiring-harness conversion with the Zener-diode polarity reversed accordingly--it charged the battery just fine with the standard Commando rotor, stator and rectifier



Tim Kraakevik
kraakevik@voyager.net
 
kraakevik said:
The 850 E-Bay chopper I sold recently had a negative-ground wiring-harness conversion with the Zener-diode polarity reversed accordingly--it charged the battery just fine with the standard Commando rotor, stator and rectifier



Tim Kraakevik
kraakevik@voyager.net

Useful info. How was the Zener diode mounted?
 
No need. I can visualise that. I always wonderd if it would survive with no heatsinking.
 
Old Bloke said:
No need. I can visualise that. I always wonderd if it would survive with no heatsinking.

Two things: One, must have heat sink. The Zener "regulates" the voltage by bleeding off excess current to ground; It does this by converting it to heat. We can't regulate the alternator in our bikes in the sense where a car's voltage regulator can actually modifiy the alternator's output, since the Lucas alternator puts out power in direct relation to the crank rpm. Picture no headlight, running at six grand. That power from the alternator has to go somewhere. Lots of heat to dissipate.
Two, positive to negative ground conversion requires reverse-polarity zener AND rectifier. Nathan
 
Nathan

You might very well be right about the polarity of the rectifier--my chopper may have had an aftermarket rectifier--please weigh in, you folks who have converted Commandos to negative-ground systems.

The chopper I sold had a conventional rotor, stator and diode--and it worked perfectly.

I don't remember whether the rectifier was stock--but the diode--which may have been hooked up backwards--was a standard unit



Tim Kraakevik
kraakevik@voyager.net
 
kraakevik said:
Nathan

You might very well be right about the polarity of the rectifier--my chopper may have had an aftermarket rectifier--please weigh in, you folks who have converted Commandos to negative-ground systems.

The chopper I sold had a conventional rotor, stator and diode--and it worked perfectly.

I don't remember whether the rectifier was stock--but the diode--which may have been hooked up backwards--was a standard unit



Tim Kraakevik
kraakevik@voyager.net

I need to revise my earlier statement about needing a different rectifier. When I first responded, I was looking at one from my junk drawer that has only three connections; two for the alternator, and one for the negative lead to the battery (the mounting post is the fourth connection for the positive ground to the frame). After pulling the seat off my '74 Interstate, I see that its rectifier has four distinct connections. In this light, all you would need to change is the Zener(s), and swap the red and green wires from the rectifier. Cheaper yet!
 
(quote) I need to revise my earlier statement about needing a different rectifier. When I first responded, I was looking at one from my junk drawer that has only three connections; two for the alternator, and one for the negative lead to the battery (the mounting post is the fourth connection for the positive ground to the frame). After pulling the seat off my '74 Interstate, I see that its rectifier has four distinct connections. In this light, all you would need to change is the Zener(s), and swap the red and green wires from the rectifier. Cheaper yet![/quote]


I don't think that is correct, I'd thought the same thing but it looks like the four terminal rectifiers have one labeled "stud"....so if it were mounted to the frame you would indeed need the correct polarity and they are sold in negative and positive ground versions...you had it right the first time.

see http://www.oldbritts.com/17_49072r.html

Zener diode polarity
 
Status
Not open for further replies.
Back
Top